Glue Products
Cyanoacrylates / Super Glues
-
Cyanoacrylate adhesives (super glue) are one-part acrylate adhesives that cure instantly on contact with mated surfaces through a reaction with surface moisture.
High strength, excellent adhesion to a wide variety of substrates, especially plastics.
When selecting between cyanoacrylate adhesives look at the following:
Viscosity
Measurement of a fluids resistance to flow. The amount of dispensed onto a surface.Working, assembly or initial set time.
Amount of time an adhesive, sealant or cement can be applied and repositioned or removed before extensive setting or curing and results in hardening of the bond joint.Gap fill
Spacing or gap between the substrate that the cyanoacrylate adhesive can accommodate and still maintain a functional, full strength bond.Ultimate tensile strength (UTS) Amount of applied stress required to cause failure in a control specimen of the material under tensile load conditions.
Use Temperature
Range that the cyanoacrylate adhesive can be exposed to without degradation of structural or other required end-use properties.Various types of dispenser
Gels, liquids, and pastes. Gel cyanoacrylate adhesives are more run resistant during application. Liquid cyanoacrylate adhesives can be used to fill deep gaps more effectively than other adhesive forms. Paste adhesives are very resistant to running, but greater force is required to dispense and spread the adhesive paste on the surface.
We also supply activators and needles to work along side this product. For more information please get in touch:
-
To Place an order call or message: 07940 422390 adhesivebrokerssolutions@hotmail.com
Activators
-
Activators
Directions:
Hold can upright whilst spraying. 200 ml & 400ml Spray Can / 1 litre tins
-
To Place an order call or message: 07940 422390
adhesivebrokerssolutions@hotmail.com
AB121 / Pink & Green
-
AB121 High Strength, High Speed, Structural Adhesive.
Do you need to bond two materials together quickly and achieve a very high bond strength? AB121 structural adhesives are the solution. AB121 is range of high strength, fast curing, 2-component structural adhesives that are used and trusted by thousands of businesses in very demanding applications. AB121 will bond most material combinations in just 5 minutes. VOC Free
AB121 is a second generation Acrylic adhesive designed to combine the high shear and temperature resistance of a conventional acrylic with the qualities of a rubber toughened adhesive where high peel and impact strength are a feature.
Applications:
AB121 adhesive bonds to a wide variety of materials, such as metals, glass, epoxy, unsaturated polyesters, GRP, Bakelite etc
Ideal for engineering, electronics, lift manufacturing, jewellery, loudspeaker manufacturer, model making and many other industries.
This product comes in a range of sizes:
25ml syringe.
50ml cartridge (Applicator gun and nozzles required).
500ml Bottle kits.
1kg tub kits.We also supply applicator guns and nozzles for these products.
-
To Place an order call or message: 07940 422390 adhesivebrokerssolutions@hotmail.com
Kommerling Korapur 784/5
-
Kommerling Korapur 784/5 50ml Black.
A range of one and two component polyurethanes used for sealing and bonding in the manufacture of vehicle body work, providing good adhesion to a wide variety of substrates including primed and varnished metals, GRP, aluminium and Duro-plastics.
This product comes in a foil pack containing two double barrelled 50ml cartridges with two nozzles
Over paintable after curing. The Korapur two component reactive adhesive is used for bonding substrates in the assembly of vehicle bodies including bonding profiles and corner angles, side walls, floors and roofs in the manufacture of sandwich elements.
This tough range of adhesives has good resistance to humidity and weathering.
For bonding ABS, rigid PVC, GRP, steel and aluminium.
Polyurethane, two component, solvent-free.
When using Körapur 784, the bond can be exposed to light strain after 12 hours. Final bond strength is reached after 24 hours. High temperatures will shorten the curing time, low temperatures will lengthen it.
Cure time 5 minutes.
Official distributer in the UK and Certified Partners for industrial adhesives and sealants of Kommerling.
We also stock extra nozzles and applicator guns.
Priced per pack and available in bulk.
-
To Place an order call or message: 07940 422390 adhesivebrokerssolutions@hotmail.com
Triple - A
-
Triple - A has been specifically designed for the bonding of Metals, Plastics, Ceramics etc.
Suitable for all industries, including, Engineering, Electronics, lift Manufacturers, Jewellery, Dental Technicians, Loudspeaker Manufacturers.
VOC Free.
The Health & Safety Benefits of Triple - A are centred around the low odour and increased flashpoint, radically reducing the need for a high degree of ventilation and the risks associated with highly flammable product.
High Bond Strength
Impact Resistant
High Heat Resistance
Non-Stringing
Fast Cure
Non-Solvented
Low Odour
Easy to apply
Bead on Bead technology.
50ml cartridge.
We also supply the necessary accessories to go along side this product.
-
To Place an order call or message: 07940 422390 adhesivebrokerssolutions@hotmail.com
Epoxies
-
Suitable for metal, ceramics, glass, wood, plastics, fabrics etc
Most epoxies are two-part adhesives cured at room temperature Thermally cured or thermoset one-part epoxies systems are also available. Depending on the formulation, epoxy resins are used as potting agents, resin binders in fibreglass construction, electrical conductors and various structural bonding applications.
Epoxies require clean surfaces compatible with the adhesive.
High strength / tough
low shrinkage during cure
resistance to chemical and environmental damage
Setting styles include:
single component setting
dual-component setting
thermosetting curing
radiation curing (which includes UV, EB and visible light curing)
Single component epoxy adhesives
Single component epoxy adhesives consist of one resin that hardens by reaction with surface moisture, a surface applied activator-primer, or through the application of heat.
Dual or multi-component adhesive or sealant systems consist of two or more resins or a resin and a hardener, crosslinker, activator or catalyst that when combined react and cure into a polymerised compound or bond. Two component epoxy adhesive systems are mixed and then applied.
Thermoset epoxy adhesives are crosslinked polymeric resins cured using heat or heat and pressure. Cured thermoset resins do not melt and flow when heated, but they may soften. Phenolic, melamine and urea formaldehyde resins are thermosetting adhesives that offer strong bonds and good resistance to high temperatures. Vulcanisation is a thermosetting reaction involving the use of heat and/or pressure in conjunction with a vulcanising agent, resulting in greatly increased strength, stability and elasticity in rubber-like materials. RTV silicone rubbers are room temperature vulcanising materials. The vulcanising agent is a crosslinking compound or catalyst. Sulphur is the traditional vulcanising agent used with natural rubber.
Silicones use moisture, acetic acid and other compounds as curing agents.
UV or radiation cured epoxy adhesives use ultraviolet light, visible light or electron bean irradiation to initiate curing, which allows a permanent bond without heating or excessive heat generation. One disadvantage of UV curing adhesives is the requirement that one substrate is UV transparent. Some UV resin systems employ a secondary curing mechanism to complete curing of adhesive regions shielded from the UV light.
EB curable epoxy adhesives use electron beam radiation to cure or initiate curing. The electron beam can penetrate through material that is opaque to UV light.
Available in:
250ml Bottle Kits
50ml Cartridges
25ml Syringes
2 x 15ml Tubes (3 min bond) - limited stock
We also supply applicator guns and mixer nozzles to go along side this product.
-
To Place an order call or message: 07940 422390 adhesivebrokerssolutions@hotmail.com
Aquabond 50
-
Aquabond 50 is a one part adhesive that adheres well to many materials including flexible PVC and Vinyl's, fabrics, leather, canvas, board and many others, to wood, metal, MDF, chipboard etc. -most combinations are worth a try - all that's needed is one surface with some absorbency.
Aquabond 50 is a one part adhesive that adheres well to many materials including flexible PVC and Vinyl's, fabrics, leather, canvas, board and many others, to wood, metal, MDF, chipboard etc. -most combinations are worth a try - all that's needed is one surface with some absorbency.
The high viscosity works well with porous materials and its thixotropic nature allow for ease of brushing etc. The high initial tack is beneficial for early handling of the products after bonding.
Aquabond 50 is excellent for the covering of partitions and panels.
Coverage, dependant upon the materials being bonded is up to 20 sq metres per litre.
Available in 25 litre and 5 litre jerrycans.
-
To Place an order call or message: 07940 422390 adhesivebrokerssolutions@hotmail.com
Hot Melt
-
Glue guns can be used for wood working, electrical, arts & crafts, floristry, flooring, product assembly etc the guns are low cost, portable and can apply hot melt in a bead or spray application.
There is a wide selection of models available and a variety of glue stick formulations to best match your application.
Glue guns can be used for wood working, electrical, arts & crafts, floristry, flooring, product assembly etc the guns are low cost, portable and can apply hot melt in a bead or spray application.
There is a wide selection of models available and a variety of glue stick formulations to best match your application.
-
To Place an order call or message: 07940 422390 adhesivebrokerssolutions@hotmail.com
Accessories
-
Our bottles start from 20g – 1 litre bottles, in round and oval styles.
We sell various sizes and styles of nozzles, needles, whiskers and plastic tubing for application purposes.
Our bottles start from 20g – 1 litre bottles, in round and oval styles.
We sell various sizes and styles of nozzles, needles, whiskers and plastic tubing for application purposes.
Surface primers and activators also available.
Activators – available for difficult to bond substrates for both pre and post cure.
-
To Place an order call or message: 07940 422390 adhesivebrokerssolutions@hotmail.com
Adhesive Guide
Any Questions?
Disclaimer:
Adhesive Brokers Solutions Limited do not accept and liability for loss or damage arising directly or indirectly from the use of these products. Customers should satisfy themselves by appropriate trials that each product is suitable for its intended use.